We've found this great article relating to Installing A Bathtub down the page on the net and thought it made perfect sense to discuss it with you on this page.
Setting up a tub isn't precisely brain surgery, however it does call for strong plumbing, carpentry, and sometimes, tiling abilities. Replacing an old bathtub with a brand-new one is additionally a moderately tough task. If the old bathtub is conveniently accessible, the project can move rapidly; if you have to open a wall surface to get rid of the old bathtub as well as position the new bath tub, the task is much harder. In either instance, the job is within a house handyman's abilities, although you will require a helper to leave the old tub and also set in the new one. See to it you have qualified yourself for the work and fit trying it. Instead of employing a specialist to take control of a halfway-completed task, it is much better to consider employing one prior to you begin. Chances are you may need an expert plumber to make tube connections.
This post will certainly help you mount a brand-new tub in your shower room if you have currently gotten a new bathtub as well as don't require to change the arrangement of your previous water supply pipelines.
Your tools and material list need to comprise the following:
Planning for the Installation
Firstly, the sustaining structure supplied with the bath needs to be fitted (if needed) according to the manufacturer's guidelines. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is essential to see to it that if the tap comes with a plastic washer, it is fitted in between the bath and the taps. On a plastic bath, it is also reasonable to fit a supporting plate under the taps unit to stop stress on the bathtub.
Fit the flexible tap adapters to the bottom of both taps using 2 nuts and also olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet via the hole in the bath. Utilize the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. See to it you utilize every one of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bath should now be ready to be suited its last setting.
Removing Old Taps
If you require to change old faucets with new ones as a part of your installment, after that the first thing you must do is separate the water. After doing so, activate the taps to drain any type of water continuing to be in the system. The procedure of getting rid of the existing taps can be fairly problematic due to the limited gain access to that is often the case.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipelines to the taps. Have a towel ready for the continuing to be water that will certainly originate from the pipelines. Once the supply pipes have actually been removed, utilize the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from turning throughout this procedure. When the faucets have been eliminated, the holes in the bath/basin will need to be cleansed of any type of old sealing substance.
Before proceeding to fit the new taps, contrast the pipe connections on the old faucets to the new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Mounting the Tub
Making use of the two wooden boards under its feet, place the bathtub in the required setting. The wood boards are helpful in evenly spreading the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto four little factors.
The following objective is to guarantee that the bath tub is leveled all round. This can be attained by checking the spirit level and adjusting the feet on the bathtub until the spirit level reviews degree.
To mount faucets, fit the bottom of the furthest adaptable faucet port to the suitable supply pipe by making a compression join; after that do the same for the other tap.
Switch on the water system and inspect all joints as well as brand-new pipework for leakages and also tighten them if essential. Fill the bathtub as well as also check the overflow electrical outlet as well as the typical outlet for leakages.
Lastly, repair the bathroom paneling as described in the supplier's user's manual. Tiling as well as securing around the bathtub needs to wait until the bath tub has been made use of at least once as this will certainly resolve it right into its last setting.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will need a plastic adapter to avoid damages to the thread. One end of the port fits on the plastic tail of the tap and also the various other end provides a connection to the existent supply pipelines.
If you need to fit a monobloc, then you will call for minimizing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next, position the tap in the installing hole in the bath/basin making sure that the washing machines remain in location between the tap and also the sink. Safeguard the faucet in place with the manufacturer offered backnut. Once the faucet is firmly in position, the supply pipelines can be connected to the tails of the taps. The taps can either be attached by using corrugated copper piping or with typical tap ports. The former kind should be attached to the tap ends initially, tightening just by hand. The supply pipelines can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the area where the bath fulfills the tile, it is essential to seal the accompanies a silicone rubber caulking. This is essential as the fitting can relocate sufficient to crack a rigid seal, causing the water to pass through the wall surface between the bath and the tiling, causing problems with dampness and also feasible leakages to the ceiling below.
You can pick from a selection of coloured sealants to blend in your components and also fittings. They are offered in tubes and also cartridges, as well as are capable of securing voids approximately a width of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of drenched newspaper or soft rope. Bear in mind to always fill the tub with water prior to securing, to enable the motion experienced when the tub remains in use. The sealant can break fairly very early if you do not think about this movement prior to securing.
Additionally, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are likewise easily offered on the market. It is a good idea to fit the floor tiles making use of waterproof or water resistant adhesive as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you really like reading up on Tools You Need to Install a New Bathtub ? Write a remark directly below. We will be pleased to listen to your thoughts about this blog entry. We hope that you come back again in the future. Be sure to set aside a second to share this write-up if you liked it. I thank you for reading our article about How to Install a Bathtub.
We're the solution!